NEW WR55X10942 Replacement Control Board Compatible for GE Refrigerator, PS2364946, WR55X10942P, WR55X11130, WR55X10552, WR55X10656, WR55X10996, WR55X11072, 200D4852G010 Primeco Brand - 1 YEAR W

I bought this controller to replace the defective one in my 20 year-old GE Profile refrigerator and it works flawlessly. It was a quick and easy installation and I am happy to be able to fix the problem myself, without having to pay to a local appliance repair tech $500+ (for OEM part & labor)!

After the power outage the refrig stopped working (GE Profile PSS26MSRC). The lights were on but the water dispenser did not work and the compressor did not start. This is a 15 year old refrig so I did not want to spend $400+ for the OEM board. Instead I bought this one and installed it. The refrig is working again. Installation was easy (10 minutes), just be careful as you pull the wire connectors from the old board. Mark the connectors and take a picture before removing them.

IMPORTANT UPDATE TO THE REVIEW BELOW: While this board brought the fridge to life, I realized after a day or two that the fruit and vegetables were freezing. The damper was functioning and the thermistors were ok but I replaced them anyway. This failed to solve the problem and the temperature was completely unresponsive to the warmer/colder settings for the freezer and fresh food part. I contacted the seller and his closing comment was that I should buy a GE original board. This board was advertised to replace the WR55X10996 board originally in my fridge, but obviously it does not function properly in my refrigerator.ORIGINAL REVIEW: This worked like a charm for my bottom-freezer GE refrigerator Model gdsl3kcycrls, whose control board was fried during a power outage last week. In that outage, one of the resistors that is part of the "snubber" circuit to protect the evaporator motor was burned, the one next to it that apparently protects the condenser fan was not. See the picture of my old board, attached. I tested both fans and they worked fine, but the board was fried. IMPORTANTLY, on my model, the left-most connector that goes to (what I believe is) J5 is only a 5-pin connector. It has orange, red and purple wires. The new board has a 9-pin connector. So I had to trim off the little piece of plastic on the housing of the female connector and plug it in to the last 5 pins of the 9 pin connector that is on the left side of the new board, sitting there all by itself next to the 3 power pins. It's obvious which end this 5-pin connector should be attached to, because the second pin is missing on the female and male connectors. The fridge won't work if you don't connect this connector.

Drop in replacement for a board identified as faulty. Half the cost of the GE official replacement board. Make sure you connect all the harnesses connected properly and that the original board didn't fail due to an issue somewhere else (new board will obviously just fail too)EDIT: 3 months later and my fridge is still running strong!

This worked great for our GSL25XGWSS GE Profile fridge. It was easy to swap out and the fridge and freezer started right up again. Huge money saver over replacing the fridge or paying someone to install for me.

Saved me from having to buy another refrigerator. Note that it recommends that you make sure other components like the evaporator fan is working before you replace this. I replaced my evaporator fan first because I thought it was the only problem. This part was easy to install.

Worked for one week then stopped sending defrost command so evaporator froze up, had to reinstall original board with less critical issues to use refrigerator. Board paperwork claims one year warranty but return policy is only 30 days, buyer beware!

This part revived my refrigerator and saved me from needing to buy a new one. Noticed the ice maker began to work intermittently, then the indicator light would fade out and it would not dispense ice at all. I noticed the compressor and fan suddenly stopped running. Determined it was the control board. The new one had a couple extra components that the old one did not, but this also was the updated part that is used in other refrigerators as well. It was easy to install. It has been a few days since I've replaced the part and so far so good.